This article may require copy ing for tone. (October 2021)
In statistics, the standard score is the number of standard deviations by which the value of a raw score (i.e., an observed value or data point) is above or below the mean value of what is being observed or measured. Raw scores above the mean have positive standard scores, while those below the mean have negative standard scores.
It is calculated by subtracting the population mean from an individual raw score and then dividing the difference by the population standard deviation. This process of converting a raw score into a standard score is called standardizing or normalizing (however, "normalizing" can refer to many types of ratios; see normalization for more).
Standard scores are most commonly called z-scores; the two terms may be used interchangeably, as they are in this article. Other terms include z-values, normal scores, standardized variables and pull in high energy physics.
Computing a z-score requires knowing the mean and standard deviation of the complete population to which a data point belongs; if one only has a sample of observations from the population, then the analogous computation with sample mean and sample standard deviation yields the t-statistic.
If the population mean and population standard deviation are known, a raw score x is converted into a standard score by
The absolute value of z represents the distance between that raw score x and the population mean in units of the standard deviation. z is negative when the raw score is below the mean, positive when above.
Calculating z using this formula requires the population mean and the population standard deviation, not the sample mean or sample deviation. But knowing the true mean and standard deviation of a population is often unrealistic except in cases such as standardized testing, where the entire population is measured.
When the population mean and the population standard deviation are unknown, the standard score may be calculated using the sample mean and sample standard deviation as estimates of the population values.
In these cases, the z-score is
In either case, since the numerator and denominator of the equation must both be expressed in the same units of measure, and since the units cancel out through division, z is left as a dimensionless quantity.
The z-score is often used in the z-test in standardized testing – the analog of the Student's t-test for a population whose parameters are known, rather than estimated. As it is very unusual to know the entire population, the t-test is much more widely used.
The standard score can be used in the calculation of prediction intervals. A prediction interval [L,U], consisting of a lower endpoint designated L and an upper endpoint designated U, is an interval such that a future observation X will lie in the interval with high probability , i.e.
For the standard score Z of X it gives:
By determining the quantile z such that
In process control applications, the Z value provides an assessment of how off-target a process is operating.
When scores are measured on different scales, they may be converted to z-scores to aid comparison. Dietz et al. give the following example comparing student scores on the (old)SAT and ACT high school tests. The table shows the mean and standard deviation for total score on the SAT and ACT. Suppose that student A scored 1800 on the SAT, and student B scored 24 on the ACT. Which student performed better relative to other test-takers?
The z-score for student A is
The z-score for student B is
Because student A has a higher z-score than student B, student A performed better compared to other test-takers than did student B.
Continuing the example of ACT and SAT scores, if it can be further assumed that both ACT and SAT scores are normally distributed (which is approximately correct), then the z-scores may be used to calculate the percentage of test-takers who received lower scores than students A and B.
"For some multivariate techniques such as multidimensional scaling and cluster analysis, the concept of distance between the units in the data is often of considerable interest and importance … When the variables in a multivariate data set are on different scales, it makes more sense to calculate the distances after some form of standardization."
In principal components analysis, "Variables measured on different scales or on a common scale with widely differing ranges are often standardized."
"The standardized regression slope is the slope in the regression equation if X and Y are standardized… Standardization of X and Y is done by subtracting the respective means from each set of observations and dividing by the respective standard deviations… In multiple regression, where several X variables are used, the standardized regression coefficients quantify the relative contribution of each X variable."
However, Kutner et al. (p 278) give the following caveat: "… one must be cautious about interpreting any regression coefficients, whether standardized or not. The reason is that when the predictor variables are correlated among themselves, … the regression coefficients are affected by the other predictor variables in the model … The magnitudes of the standardized regression coefficients are affected not only by the presence of correlations among the predictor variables but also by the spacings of the observations on each of these variables. Sometimes these spacings may be quite arbitrary. Hence, it is ordinarily not wise to interpret the magnitudes of standardized regression coefficients as reflecting the comparative importance of the predictor variables."
If the random variable under consideration is the sample mean of a random sample of X:
then the standardized version is
In bone density measurements, the T-score is the standard score of the measurement compared to the population of healthy 30-year-old adults.